Mini Portable Guitar Amplifier

Posted in Amplifiers, on 2015-06-14

Circuit diagram:

Mini Portable Guitar Amplifier

Parts:

  • R1______________22K 1/4W Resistor
  • C1______________10µF 25V Electrolytic Capacitor
  • C2_____________100nF 63V Polyester or Ceramic Capacitor
  • C3_____________220µF 25V Electrolytic Capacitor
  • IC1__________TDA7052 Audio power amplifier IC
  • J1,J2__________6.3mm Stereo Jack sockets (switched)
  • SPKR___________8 Ohm Loudspeaker (See Notes)
  • B1________________9V PP3 Battery or 3V Battery (2 x 1.5V AA, AAA Cells in series etc.) Clip for PP3 Battery or socket for 2 x 1.5V AA or AAA Cells

Comments:

This small amplifier was intended to be used in conjunction with an electric guitar to do some low power monitoring, mainly for practice, either via an incorporated small loudspeaker or headphones. The complete circuit, loudspeaker, batteries, input and output jacks can be encased in a small box having the dimensions of a packet of cigarettes, or it could be fitted also into a real packet of cigarettes like some ready-made units available on the market. This design can be used in three different ways:

  • Loudspeaker amplifier: when powered by a 9V alkaline battery it can deliver about 1.5W peak output power to the incorporated loudspeaker.
  • Headphone amplifier or low power loudspeaker amplifier: when powered by a 3V battery (2x1.5V cells) it can drive any headphone set type at a satisfactory output power level or deliver to the incorporated loudspeaker about 60mW of output power. This configuration is useful for saving battery costs.
  • Fuzz-box: when powered by a 3V battery (2x1.5V cells) and having its output connected to a guitar amplifier input the circuit will behave as a good Fuzz-box, showing an output square wave with marked rounded corners, typical of valve-circuits output when driven into saturation.

Notes:

  • For the sake of simplicity and compactness, this unit employs a dual bridge IC amplifier and a few other parts. For the same reason no volume or tone controls are provided as it is supposed that the controls already existing on the electric guitar will serve satisfactorily to the purpose.
  • No power switch is used: the battery voltage will be applied to the circuit when the input plug will be inserted in the input jack socket J1. For this purpose be sure that the input plug is a common 1/4 inch guitar mono jack plug and J1 is a 1/4 inchstereo jack socket. The output jack socket J2 must be a switched stereo type. The changeover switching is arranged in such a way that, when a common headphones stereo jack plug is inserted into the socket, the loudspeaker will be disabled and the mono output signal will drive both the headsets in series, allowing full headphone reproduction. When used as a Fuzz-box output, a mono jack plug must be inserted into J2. If the amplifier is intended to be encased in a packet of cigarettes, standard loudspeaker diameter should be 57 or 50mm.

Technical data:

  • Max output power: 1.5W @ 9V supply - 8 Ohm load; 60mW @ 3V supply - 8 Ohm load
  • Frequency response: Flat from 20Hz to 20kHz
  • Total harmonic distortion @ 100mW output: 0.2%
  • Max input voltage @ 3V supply: 8mV RMS
  • Minimum input voltage for Fuzz-box operation: 18mV RMS @ 3V supply
  • Current consumption @ 400mW and 9V supply: 200mA
  • Current consumption @ 250mW and 9V supply: 150mA
  • Current consumption @ 60mW and 3V supply: 80mA
  • Quiescent current consumption: 6mA @ 9V, 4mA @ 3V supply
  • Fuzz-box current consumption: 3mA @ 3V supply

If you like this page, please consider sharing

Credits

Source